xCall Us

Always Plumbing & Heating

300 - 17633 114 Ave NW
Edmonton, AB T5S 2R9 CA

Guide to DIY Washing Machine Installation and Common FAQs

Guide to DIY Washing Machine Installation and Common FAQs

Installing a new washing machine in your home may seem like a challenging task, but with the right guidance, it can be a manageable DIY project. Whether you’re replacing an old unit or setting up a washing machine for the first time, this step-by-step guide will help you through the process. We’ll also address common questions about washing machine installation to ensure a smooth and trouble-free setup.

How to Install a New Washing Machine in Your Home

Tools and Materials You’ll Need

Before you begin, gather the necessary tools and materials for the job:

  • New washing machine
  • Washer hoses (usually included with the machine*)
  • Adjustable wrench
  • Screwdriver
  • Level
  • Pipe tape
  • Drain hose clamp
  • Drain hose holder
  • Bucket or towel (for water cleanup)
  • Safety goggles

*Using a corrugated steel tube piping is recommended instead of the included rubber-based tubes that come with the machine as they are prone to rupture. Insurance companies say this is one of the biggest claims, as these rubber pipes burst for no apparent reason.

You may already have many of these items around your house or garage. If you’re missing any of them, make a quick trip to your local hardware store. Pipe tape, hose clamps, and a level are absolutely essential for a leak-free installation. Once you have everything you need to begin the job, follow the steps outlined below. 

Step 1: Choose the Location

Select a suitable location for your washing machine. Ensure it’s on a level surface, as this is essential for proper operation. Leave enough space around the unit for ventilation and easy access to hoses and connections. Check the manufacturer’s recommendations for specific clearance requirements.

Step 2: Prepare the Area

Clear the area and clean it thoroughly. This will help you spot any potential issues or leaks more easily. If you’re replacing an old washing machine, disconnect and remove it from the space. Be prepared for some water spillage during this step, so keep a bucket or towel handy.

Step 3: Install the Washer Hoses

Connect the hot and cold water supply hoses to the back of the washing machine. Typically, the hot water supply is marked in red, and the cold water supply is marked in blue. Make sure to attach them to the correct water source.

Use an adjustable wrench to tighten the hose connections. Be careful not to overtighten, as this can damage the threads.

Step 4: Attach the Drain Hose

Connect the washing machine’s drain hose to the drain pipe. Ensure the drain hose is securely fastened to the pipe to prevent leaks. You can use a drain hose clamp for added security.

Place a drain hose holder over the edge of the laundry tub or standpipe. This prevents the hose from moving out of place during the wash cycle.

Step 5: Level the Machine

To avoid vibrations and noise during operation, it’s crucial to level the washing machine. Place a level on top of the unit and adjust the legs until the bubble is centered in the level’s indicator.

Once you’ve leveled the machine, give it a gentle push to ensure it doesn’t wobble or move easily. A stable machine won’t shift during the wash and spin cycles, preventing potential accidents and damage.

Step 6: Plug In the Machine

1. Pre-Plug Inspection: Before you proceed, take a moment to carefully inspect the electrical plug. Look for any cuts, fraying, or signs of wear on the cord. If you detect any damage to the cord or plug, do not connect it to the outlet. Contact the manufacturer or the store where you purchased the washer for a replacement.

2. Secure Connection: Once you’ve confirmed that the plug is in good condition, connect the washing machine to a nearby electrical outlet. Ensure that the outlet is easily accessible, and there are no obstacles obstructing the plug’s insertion.

3. Grounding: Grounding your washing machine is a critical safety measure. Ensure that it’s connected to a properly grounded electrical outlet. A grounded outlet reduces the risk of electrical shocks and ensures safe operation.

If everything looks good at this point, continue to the next step. You can plug in your washing machine with confidence, knowing that you’ve prioritized safety and a secure electrical connection. This sets the stage for a trouble-free laundry experience.

Step 7: Test the Machine

Before you start a full load of laundry, run a test cycle with an empty machine. This helps ensure that there are no leaks and that the washing machine is functioning correctly.

Common Questions and Tips:

1. Do I need a plumber to install a washing machine?

In most cases, you don’t need a plumber to install a washing machine. If you have basic plumbing skills and follow the manufacturer’s instructions, you can typically handle the installation yourself. However, if you’re uncomfortable with plumbing tasks or face complex issues, it’s wise to consult a professional plumber.

2. How should a washing machine drain pipe be?

The washing machine’s drain pipe should be properly connected to a standpipe or a laundry tub. The standpipe should be at least 2 inches in diameter and located no more than 96 inches above the floor. Ensure the drain hose is securely attached to prevent water leaks during the machine’s operation.

3. What is the code for a washing machine drain?

Washing machine drain codes may vary by location, so it’s essential to check your local plumbing codes and regulations. These codes typically address issues like proper drainpipe size, venting, and drainage capacity. Complying with local codes is crucial to ensure a safe and effective installation.

4. How much space do you need behind a washing machine for the pipes?

You’ll need approximately 4 to 6 inches of space behind the washing machine to accommodate the water supply hoses and drain hose. Be sure to measure and provide enough clearance for the connections to fit comfortably.

5. Do you connect a washing machine to hot or cold water?

Most washing machines allow you to connect to both hot and cold water supplies. However, many modern machines are designed to be more energy-efficient and primarily use cold water. Always check the manufacturer’s instructions to determine the recommended water temperature settings for your specific machine.

6. Does a washing machine need a floor drain?

A floor drain is not mandatory for a washing machine, but it can be a valuable addition. A floor drain can help manage any accidental water leaks or overflows, preventing water damage to your home. It’s a good safety feature, especially if your laundry area is on an upper floor.

Seeking Professional Assistance

Not everyone is a natural when it comes to home improvements, and that’s perfectly fine. Installing a washing machine may seem straightforward, but it can still be a challenging task for some. If you’re uncertain about any aspect of the installation or if you encounter unexpected difficulties, it’s always a wise choice to reach out to a licensed professional plumber.

Licensed plumbers have the experience and expertise to handle a wide range of plumbing tasks, including washing machine installations. They are well-versed in local plumbing codes and regulations, ensuring that the installation complies with all necessary standards.

If any of these scenarios apply to your situation, contacting a professional plumber is a good idea:

Complex Plumbing Systems: If your home has a complex plumbing system, you may need the insight of a professional plumber to navigate and make the necessary connections correctly.

Limited DIY Skills: Not everyone feels comfortable working with plumbing fixtures and connections. If you lack experience or confidence in your DIY skills, hiring a professional can give you peace of mind. Every home is different and even if you’ve done it before, you can still experience problems that you may not be able to handle on your own.

Custom Installations: If your washing machine installation requires custom modifications or unique solutions, a licensed plumber can provide the expertise needed to tackle these challenges.

Unexpected Issues: Sometimes, you may encounter unforeseen issues during the installation, such as hidden leaks or damaged plumbing. A professional plumber can quickly identify and address these problems.

Safety Concerns: If you’re concerned about safety risks related to plumbing tasks, especially in older homes with outdated systems, professional plumbers have the knowledge and equipment to work safely.

Remember that there’s no shame in asking for help, especially when it comes to complex tasks like plumbing. Contacting a licensed professional plumber ensures that your washing machine installation is done correctly, efficiently, and in compliance with all relevant codes. It’s a smart investment in your home’s functionality and your peace of mind.

At Always Plumbing and Heating in Edmonton, your comfort and safety are our top priority. If you need help with a plumbing installation, repair, or advice on new fixtures for your bathroom faucet, we can help. Our plumbers are experts when it comes to installing and repairing all types of plumbing systems. We guarantee customer satisfaction and strive to provide you with the best service possible. Contact us today to learn more.

Contact Us

Your Name(Required)